micro USB powered 27v COLLOIDAL SILVER generator with stirring and current limited circuit
Silver-eMed C07 is complete end to end solution so you can make your own safe, micro-particle, therapeutic colloidal silver water (full kit).
Our product is designed to produce the smallest particles in size with range from 001 to .01 microns (10 to 100 angstroms) or (1 to 10 nanometers). That is the size of silver particles that best absorb light in the indigo range, leaving only its inverse color, transparent to yellow, to be observed.
Silver-eMed Technical specifications:
o Build-in step-up power module converting 5V (USB) to 27V (output voltage)
o Output current limited to 2mA
o Automatic mechanic stirring 30 rpm (low noise)
o Removable/replaceable silver electrodes
o Flask Erlenmeyer borosilicate glass 250 ml (production vessel)
o 2 position on/off power switch
o Blue LED operation indicator
o Short circuit protection
Why you should consider our solution and use it with confidence?
Our product is designed to produce high quality colloidal/ionic silver water compromising nothing in the process.
Fit for purpose: Our product is designed to produce the smallest particles in size with range from 001 to .01 microns (10 to 100 angstroms) or (1 to 10 nano-meters). That is the size of silver particles that best absorb light in the indigo range, leaving only its inverse color, transparent to yellow, to be observed. It has a build-in step-up power module converting 5V to 27 volts and current limiting circuit output to 1mA.
Fit for use: Powered by micro USB cable you can power the device from any USB port (computer, phone charger or Power Bank). Due to the current limiting circuit the silver electrodes lifespan is significantly increased as well as the device extended operation on external battery supply. Using the included digital TDS meter you are able to precisely measure and reach the concentrations you are targeting.
Particle size matters (smaller is better). Why we use limited current?
Any classical colloidal silver generator will produce ionic silver at the same time it is producing colloids but the key difference to produce smaller particles (ions) is limited output current to be applied. The emitted particle size depends on the intensity of the electrical current while the concentration (strength) depends on the time the current is flowing between the silver electrodes. Higher currents tend to blast off larger particles from the silver therefore we have limited the current to 2mA. Low (limited) current tends to generate smaller particles, and therefore silver ions rich solutions. Following Dr. Bob Becker’s recommendations and our own extensive research in producing high quality colloidal silver water the optimal direct current output appears to be within the range of 25-30 volts.
Complete unit includes:
1. Silver-eMed Colloidal Silver Generator
2. 2x10cm Ultra Pure Silver Electrodes 9999 (99.99%) 1.5mm diameter (14 Gauge)
3. Flask Erlenmeyer borosilicate glass 250 ml (production vessel)
4. High quality micro USB cable
5. Portable Digital TDS Meter 0-9990 PPM
6. Pharmaceutical grade amber glass 100ml
7. Pharmaceutical grade mist nozal spray 60ml
8. Graduated pipette dropper 3ml
9. Electrodes scouring pad
10. Silver-eMed User Manual
Why stirring the solution is important?
In parallel during the process the silver concentration within the distilled water will not be equally redistributed through the volume. It will be significantly higher closer to the electrodes. To limit the concentration of the colloid at any point you need to stir the solution during the process.
When preparing your solution give it a time to reach the concentration you are targeting. The batch cycles depends on the colloidal silver strength (ppm) you desire to achieve. Electrodes will darken in color at the end of each cycle. In order to produce high quality and pure colloidal/ionic silver water we strongly recommend you carefully clean the electrodes before each cycle (in 30 minutes intervals).
As you can see from the table the more cycles you perform the stronger the solution will get. Although the colloidal silver generator has built-in current limiting circuit, continuing the cycles and getting readings over 25-30 ppm will cause saturation. This may compromise the solution quality. We strongly recommend you stop the process before saturation is reached.
Download Silver Purity Certificate
Please, refer to the user manual for detailed step by step process walk-trough.
Download User Manual
In Stock.
Free Shipping within UK & Free Shipping to EU (all countries), US and Canada with Royal Mail International Tracked Shipping. Full refund if you don’t receive the item + 60 days Return Policy.